TDA2003 Anfi devreleri

guclusat

Tanınmış Üye
Süper Moderatör
Circuit of of power audio amplifier with tda2003 for 10 Watts potency

TDA 2003 has a better performance than the tda2002 using the same configuration of pins. Additional characteristics in relation to the tda 2002, it demands few components external, easy assembly, it is a low cost solution for an audio amplifier. A mounted amplifier with tda2003 presents protection against short of the pins with the earth. The good of setting up an amplifier with tda2003 is that he easy of being found at the market, even for who is far away from the great centers, has the possibility to do to buy him/it integrated by the internet. The tda2003 can be fed by batteries by a long period.
tda2003-esq.png
Description of the circuit of the amplifier of 10 watts simple source

It is treated of an assembly easy of being accomplished what is necessary it is just a tda2003 and one more half dozen of components.
To facilitate the assembly the circuit it counts with a circuit plate printed.
Schematic of the amplifier with tda2003

Suggestion of printed circuit board for assembly of the amplifier with tda2003. Real size.

tda2003.png
PCI side of the components to guide in the assembly of the amplifier with tda2003.

amplificador-tda2003.png
lists of components for assembly of the amplifier

Resistors:

  • R1:220 Ω
  • R2: 2.2Ω
  • R3: 1Ω 1 watt
  • Rx: 39Ω See the datasheet paw to alter the value of Rx
Capacitors

  • C1: 2.2µF 25V electrolitic
  • C2:470µF 35V electrolitic
  • C3:0.1µF polyester or ceramic
  • C4:1000µF/35 V electrolitic
  • C5: 100nF polyester or ceramic
  • C6: 100µF 35v electrolitic
  • Cx 39nF See the datasheet paw to alter the value of Cx
Semiconductors

  • IC1: TDA2003
Reference: Tda7294 St microelectronics datasheet.
www.st.com
 

Eklentiler

  • Circuit of power audio amplifier with tda2003 for 10 Watts potency.pdf
    105,8 KB · Görüntüleme: 54
Son düzenleme:
TDA2003'LÜ 10W MONO AMFİ





TDA2003 ile yapılmış yapımı kolay bir amfidir, eleman değerleri şemada belirtilmiştir, Her ne kadar besleme gerilimi 18Volt yazsada tipik kullanımı 12 volttur. Tahmini beslemeden çektiği amper tam güçte 3,5Amper gibi bir güç çeker, bu yüzden uygun bir soğutucuya bağlamak lazım entegreyi.
RX = 39ohm
CX = 39nF
Hoparlör omajı ise 4-8 Ohm'dur


 

Eklentiler

  • Tda2003Anfiı.zip
    36,2 KB · Görüntüleme: 33
3W/6W audio amplifier using TDA2003
 

Eklentiler

  • 172-15.jpg
    172-15.jpg
    67,5 KB · Görüntüleme: 16
  • 372-10-696x411.jpg
    372-10-696x411.jpg
    41,4 KB · Görüntüleme: 14
  • parts-list72-3.jpg
    parts-list72-3.jpg
    53,7 KB · Görüntüleme: 14
  • 272-15-696x394.jpg
    272-15-696x394.jpg
    29,8 KB · Görüntüleme: 15
STEREO TONE CONTROLLED 12V AMPLIFIER CIRCUIT WITH TDA2003
This audio amplifier circuit using the TDA2003 integrated circuit which has the same configuration and pinouts of the TDA2002. The interesting thing is that this integrated uses very few external components, assembly is very simple, low cost and uses little space. The TDA2003 amplifier IC provides an output current up to 3.5 A, very low harmonic and cross-over distortion. Has short circuit protection DC and AC, thermal protection above the permissible range, load dump voltage surge up to 40V and incidental breaks ground.

TDA2003 AMPLIFIER CIRCUIT SCHEMATIC

tda2003-amplifier-schematic.png

NOTE: The integrated output TDA2003 must be attached to an aluminum heat sink for the heat emitted by them is dissipated. If you put the heatsink, integrated tightly screwing on, surely the amplifier will burn in a few minutes.

4558 PREAMPLIFIER SCHEMATIC
4558-preamplifier-schematic.png

The main component of the preamplifier with tone control circuit is the integrated circuit C4558. The original is the integrated enterprise JRC4558 New Japan Radio Co., but they say only (C), at good quality as other brands. The 4558 is a dual op amp low noise. It is one of the most used in professional audio for excellent response and defined sound. You can use other replacements as the TL072, but the sound is not the same, although it is also good.
 

Eklentiler

  • STEREO TONE CONTROLLED 12V AMPLIFIER CIRCUIT WITH TDA2003.zip
    55,6 KB · Görüntüleme: 42
7 Watt Audio Power Amplifier

This small amplifier is constructed around the TDA2003 IC, capable of delivering 4Wrms at 4ohms. The TDA 2003 has improved performance with the same pin configuration as the TDA 2002. The additional features of TDA 2002, very low number of external components, ease of assembly, space and cost saving, are maintained. The device provides a high output current capability (up to 3.5A) very low harmonic and cross-over distortion. Completely safe operation is guaranteed due to protection against DC and AC short circuit between all pins and ground, thermal over-range, load dump voltage surge up to 40V and fortuitous open ground. A conventional direct current can be connected as supply.

Circuit's picture:
41-1366321978.png
Circuit diagram:
41-b-1366321978.png
Parts

R1 = 470R
R2 = 47R
R3 = 100R
R4 = 1R
C1 = 1822pF
C2 = 100nF-63V
C3 = 100nF-63v
C4 = 10uF-25V
C5 = 470uF-25V
C6 = 1000uF-35v
C7 = 1000uF-35V
IC1 = TDA2003

Specifications:

  • Music power output: 7W / 4ohm
  • RMS output: 3.5W / 4ohm or 2W / 8ohm
  • Total harmonic distortion: 0.05% (1W / 1kHz)
  • Frequency response: 20Hz to 20kHz (-3dB)
  • Signal/noise ratio: 86dB (A weighted)
  • Input sensitivity: 40mV / 150Kohm
  • Overload and short-circuit protected
  • Supply voltage: 15V DC (8 to 18V DC possible) / 0.5A
  • Dimensions: 2.2 x 1.4
 

Eklentiler

  • 7 Watt Audio Power Amplifier.zip
    133,2 KB · Görüntüleme: 51
Son düzenleme:
К174УН14 (TDA2003)

k174un14.gif

Схема усилителя на К174УН14 проста, потому что обвес этой микросхемы минимален: развязывающие конденсаторы на входе и выходе, цепочка обратной связи для необходимого коэффициента усиления - вот, практически, и вся схема. Под неё существует готовая печатная плата за неизвестным авторством.

Цепь C4R4 следует установить только в случае самовозбуждения усилителя. Изменяя соотношение резисторов R1 и R2, можно менять коэффициент усиления по минимуму искажений на максимальной мощности. Других настроек схема не требует и начинает работать сразу после включения. Максимальная амплитуда входного сигнала не должна быть больше 1 вольта.

usilitel_k174un14.jpg

Усилители на данной схеме широко применяются радиолюбители в виду своей простоты и надёжности. При мощности, близкой к максимальной, следует использовать радиатор для отвода тепла, чтобы защитить микросхему от перегрева. Возможное применение данного УНЧ - портативные колонки, переговорные устройства, музыкальные звонки и любые другие устройства, где требуется усиление звука до 5 ватт и существуют требования к простоте схемы.
 

Eklentiler

  • k174un14_TDA2003.zip
    68,6 KB · Görüntüleme: 32
10 watt bas yükselticisi

TDA 2003 yongasına yapılan tam teşekküllü bir güç amplifikatörü devresi Bu yonga oldukça yaygın. Amplifikatör, iki özdeş modül kullanan geçici bir stereo amplifikatörde de kullanılabilir ve herhangi bir fabrika cihazında arızalı bir amplifikatör değiştirilirken de kullanılabilir.

Bazen orijinal mikro devreyi bulmak imkansızdır ve bu modüler amplifikatör kurtarmaya gelir ve cihazınızı çalışmaya ve tekrar hayata döndürür.

Amplifikatör, hoparlörler veya uygun hoparlörler ile çalışmak üzere tasarlanmış küçük bir modül şeklinde yapılır.

Amplifikatörün şematik diyagramı şekilde gösterilmiştir.
1681747345340.png
TDA2003'te amplifikatör devresi
Bu, TDA2003 yongasının tipik bir katılımıdır. Bu mikro devre, kısa devre ve termik korumaya karşı dahili koruma ile donatılmıştır, çünkü mikro devrede bu arıza çok nadirdir.

Amplifikatör devre kartı makalede gösterilmektedir.
1681747378208.png
Amplifikatör devre kartı
Çok sayıda minyatür boyut için ücret tek taraflı fiberglas üzerine yapılan 2,5 cm x 4 cm'dir. Amplifikatörün montajı çok basittir ve herhangi bir soruna neden olmamalıdır. Çip ayrıca üzerine monte edildiği bir soğutma radyatörüne de ihtiyaç duyacaktır.

Amplifikatörün önemli bir elemanı ayrıca 8 ila 15 V voltajlı bir güç kaynağıdır ve buna göre çıkış akımı, mikro devrenin tüketimine karşılık gelmelidir. Düşük güç kaynağı kullanmaya çalışmak yalnızca tam güç vermekle kalmaz, aynı zamanda sinyal bozulmasına neden olur.
 

Eklentiler

  • 10 watt bas yükselticisi.zip
    84,4 KB · Görüntüleme: 42
Son düzenleme:


Amplifikatör mikro devresi, 6V / 500mA güç kaynağı kullanarak 3 W çıkış gücü ve 8-ohm 6-watt hoparlörlü 12V / 500mA güç kaynağı kullanarak 6 W çıkış sağlar.

TDA2003'ün 1 no'lu terminali 100 kΩ'luk bir dirençten eksi güce çekilen giriş terminalidir . Pin 1'e (IC1) 10kΩ potansiyometre (VR1) ve kapasitör C1 ve C2 üzerinden bir ses sinyali uygulanır . VR1 potansiyometresi, ses seviyesini ayarlamak için kullanılır.



IC1'in 3 numaralı pimi toprağa bağlı. Pim 4, hoparlör terminallerinden birine 470uF / 16V kondansatör (C5) ile bağlanan çıkıştır. Aynı zamanda eksi 0.1 μ F kapasitör (C4) ve 1 (direnç (R4) ile bağlanır.

Pin 5 IC1, S1 anahtarı üzerinden bir + 6V güç kaynağına bağlanır. Isıyı gidermek için TDA2003'ü uygun bir soğutucuya monte etmeniz önerilir.
 

Eklentiler

  • TDA2003 amplifikatörü.zip
    60,8 KB · Görüntüleme: 34
60491590.jpg
Bask devre ekte mevcuttur.
 

Eklentiler

  • tda2003.rar
    18,7 KB · Görüntüleme: 27
  • upload_2019-11-28_10-45-57.png
    upload_2019-11-28_10-45-57.png
    124,1 KB · Görüntüleme: 86
Son düzenleme:
Geri
Yukarı