1. Bu site çerez kullanmaktadır. Siteyi kullanmaya devam etmeniz halinde çerez kullanımı ile ilgili site koşullarını kabul etmiş sayılırsınız. Daha Fazlasını Öğren.
  2. Forum İllegal Uyarısı Forum kuralları gereği forumda video ve illagal paylaşım yapmak yasaktır.Program Arşivimizde ise kısıtlanmış sürüm yada dağıtımı serbest olan (trial - freeware) yazılımlar yayınlayınız..Aksi takdirde mesajlarınız silinecektir..

SatHawk/Solomend HD PVR800 Fw Version vom 30/08/2011

Konusu 'Diğer Uydu Alıcıları' forumundadır ve guclusat tarafından 3 Eylül 2011 başlatılmıştır.

  1. guclusat
    Offline

    guclusat Tanınmış Üye Süper Moderatör

    Katılım:
    14 Haziran 2009
    Mesajlar:
    9.754
    Ödül Puanları:
    48
    MAIN FEATURES

    1. Receive Digital High Definition (HD) and Standard Definition (SD) Satellite Signal
    2. Supports DVB-S, DVB-S2, MPEG-2 & MPEG-4
    3. Digital Video Recorder through USB (external flash or hard drive are not included)
    4. The most affordable FTA HD receiver on the market today.
    5. Worldwide compatible
    6. Hardware Blind Search DVB-S and DVB-S2 (fast search less than 2 Minutes on most satellites)
    7. Linux MIPS Operating System
    8. STB main IC solution is ALI , demodulator model is M3501 from Ali
    9. HD DVB-S2 SHARP 7306 Tuner
    10. Multilingual support on screen menu (OSD): English, French, Deutsch, Italian, Spanish, Swedish, Danish, Greece, Portuguese, Finland, Holland, Turkish, Czech

    The first thing to do is save the downloaded firmware file on a USB flash disk.
    Plug USB disk to the back of your receiver. It will be recognized by the receiver.

    1. Before upgrade, do a Factory Reset:

    * Go to TOOLS menu and click on Factory Settings
    * Click Yes to continue. The receiver will go to factory default and restart.

    2. Upgrade Firmware:

    * Click on MENU and go to TOOLS menu again
    * Scroll down to "Upgrade by USB"
    * Click on START
    * After the loading is completed, Accept the upgrade.
    * The receiver will restart.

    3. After upgrade, do another Factory Reset:

    * Go to TOOLS menu and click on Factory Settings
    * Click Yes to continue. The receiver will go to factory default and restart.

    >>> Version vom 30/08/2011 ! <<<


    The New Official Firmware version do not include any channels.


    Changelog:
    Zitat:
    What's New:
    In version [OPENBOX_S9_110830]
    Skybox/Openbox/Solomend S9 Firmware 30/08/11 - ShenZhen

    Confirmed Ver: OPENBOX_S9_110830

    Regrading the new software dated August 30th 2011, its main improvements are the following:

    New software has been released, made ​​the following optimization:
    1 Shows a list of programs to increase 3.
    2 Optimize the sound noise problems.
    3 Optimization CCCAM chain scission restart problem.
    4 Quick-change restart optimization problem.
    5 Optimization NDS reader questions.

    NDS Support
     

    Ekli Dosyalar:

Yüklüyor...

Sayfayı Paylaş